An automatic meter reading system is the infrastructure that reads the registers of electricity, water, gas and heat meters at regular intervals without human intervention and transfers them to a central database. In Türkiye the term covers two different things: the utility AMR (OSOS) the distribution company installs for billing, and the in-house automatic meter reading a facility installs for its own operational decisions. This article explains how the system works, how the two approaches differ, which protocols are used and how to set it up.
How does it work?
- Meter: provides register and instantaneous values through a digital output. Electricity meters use Modbus RTU over RS-485 or an optical / IEC 62056 port; water and heat meters use M-Bus or a pulse output; gas meters use a pulse output or a separate volume corrector.
- Collector (field box / data logger): polls the meters in turn and keeps the readings with timestamps in local storage.
- Communication: the collector sends the data to the centre over wired network, cellular or the internet through an encrypted channel.
- Centre: readings are stored, consumption differences are calculated, reports and alarms are produced.
Reading frequency depends on the purpose: one register per day is enough for billing; load profiling and fault detection need 15-minute or even few-second instantaneous values.
Utility AMR versus in-house system
| Feature | Utility AMR (OSOS) | In-house automatic reading |
| Purpose | Billing, grid management | Cost control, cost allocation, fault detection |
| Meters read | Only the main (official) meter | Main meter + all sub-meters (floor, tenant, feeder, machine) |
| Data owner | Distribution company; customer sees a limited portal | The facility; raw data in its own hands |
| Frequency | Usually daily / hourly load profile | Seconds to minutes; instantaneous power, voltage, cos φ |
| Scope | Electricity (gas, water under separate utilities) | Electricity + water + gas + heat on one screen |
| Alarms | None or limited | Reactive threshold, demand overrun, leakage, device offline |
They do not replace each other. Utility AMR ensures the bill is correct; the in-house system shows why the bill is what it is and how to lower the next one. Subscribers see their OSOS data on the distribution company's portal (UEDAŞ, DEDAŞ and BEDAŞ OSOS portal addresses).
Which protocols are used?
- Modbus RTU / TCP: the most common method for power analysers and electricity meters. Up to 32 devices share an RS-485 line, each with a unique address.
- M-Bus (Meter-Bus): a two-wire bus designed for water, heat and gas meters. Meters are powered from the line, and many meters over long distances share a single cable.
- Pulse output: the simplest method; each pulse equals a fixed quantity (e.g. 1 pulse = 10 litres). It carries a count rather than a register, so resynchronisation is needed after an outage.
- BACnet / IP: carries meter data on the same network in facilities integrated with a building automation system.
- Optical / IEC 62056 (DLMS): the standard reading port of official meters; usually read by the utility.
Metering in industrial zones and multi-tenant sites
Organised industrial zones, shopping centres, office buildings and housing estates distribute energy to many sub-customers from their own network. Here automatic reading does two jobs at once: by reading every tenant at the same moment with the same method it makes cost allocation indisputable, and from the difference between the main meter and the sum of sub-meters it reveals losses and theft. With manual reading, day drift between months and reading errors make that difference meaningless; with automatic reading the month-end register falls on the same minute for every meter.
Setup steps and points to watch
- Meter inventory: brand, model, communication port, address, multiplier. Meters without communication are brought into scope via pulse output or replacement.
- Line design: follow cable type, termination resistor and maximum distance rules on RS-485 and M-Bus lines; do not run them in the same tray as power cables.
- Collector location: inside the panel, at a point with uninterrupted supply and internet access. It must store data locally when the link drops and send it later.
- Time synchronisation: all readings are stamped against a single clock source; otherwise tariff period (T1/T2/T3) separation breaks.
- Verification: in the first month compare the register on the meter display with the value in the system; multiplier and address errors are caught at this stage.
- Security: the collector connects outward itself, no inbound port is left open; communication is encrypted.
Summary
An automatic meter reading system carries meter registers to the centre without human hands. The utility's AMR validates the bill; the in-house system reads main and sub-meters together, enabling cost control, cost allocation and loss detection. Modbus, M-Bus and pulse output are the three basic methods; success depends on an accurate inventory, proper line design and a collector that stores data through outages.
What is an automatic meter reading system?
Infrastructure that reads the registers of electricity, water, gas and heat meters at regular intervals without human intervention and transfers them to a central database. It consists of the meter, a collector device, a communication channel and central software.
What is the difference between utility AMR and in-house meter reading?
Utility AMR is the distribution company's system that reads only the main meter for billing; the data stays with the utility. An in-house system reads the main meter and all sub-meters for the facility's own purposes: cost control, cost allocation, loss and fault detection.
Which protocols are used to read meters?
Electricity meters and analysers are mostly read with Modbus RTU over RS-485; water, heat and gas meters with M-Bus or pulse output; facilities tied into building automation use BACnet/IP. The optical port of official meters is usually used by the utility.