📝 Industry

Critical Power in Hospitals: UPS, Generator and ATS Architecture

6S Teknoloji · 12.11.2026 · 6 min read

Critical Power in Hospitals: UPS, Generator and ATS Architecture — 6S Teknoloji

In a hospital, a power outage is not merely a comfort problem, as it is in most buildings. An anaesthesia machine in an operating theatre, a ventilator in intensive care or the cold chain in a laboratory depends directly on continuity of supply. For that reason a hospital electrical installation is not designed around a single source but as a chain of links arranged in series, each one backing up the next. This article covers the architecture of that chain, redundancy concepts, medical location groups, the isolated IT system, and what should be recorded during commissioning and periodic testing. Generator fuel and run-hour tracking and UPS battery monitoring are covered in separate articles, so they are not repeated in detail here.

The Links of the Critical Power Chain

In a typical hospital, energy travels from the distribution grid to the medium-voltage switchgear and from there to one or more transformers. The main low-voltage switchboard at the transformer output separates the busbar feeding general loads from the busbar feeding safety services. The safety busbar is connected to both the grid and the generator through an automatic transfer switch (ATS). Behind the ATS sit UPS systems for loads that tolerate no interruption at all. The final link consists of the medical panels and the IT panels.

  • Grid and medium voltage: The primary source. Where possible, a supply from two different feeders reduces the risk of a single point of failure at the very start of the chain.
  • Transformer: The number of transformers and the load split are planned around whether the remaining units can carry the critical load when one transformer is out of service.
  • ATS: When grid voltage is lost it signals the generator to start, transfers the load once the generator is ready and manages the retransfer when the grid returns.
  • Generator: The source for safety services during long outages; however, it cannot protect the load on its own during the interval before it starts and accepts load.
  • UPS: Bridges the gap between grid loss and the generator taking over, and supplies conditioned voltage to sensitive loads.
  • Medical and IT panels: The final distribution points feeding equipment in the patient environment, the nurse call system, medical gas alarms and the server infrastructure.

Redundancy: What Do N, N+1 and 2N Mean?

Redundancy is described in symbolic terms. N is the number of units needed to carry the load. N+1 means one spare unit is added to that number; if any unit fails or is taken out for maintenance, the rest continue to carry the load. 2N means a fully independent second copy of the whole system: two separate UPS groups, two separate distribution paths and dual-corded loads. Expressions such as 2N+1 describe a combination of the two approaches.

What matters is that redundancy exists not only in the number of units but also along the path the energy takes. In a design where two UPS units feed the same output panel, a fault in that panel or on a single busbar removes all of the redundancy. A design review should therefore ask, link by link, "if this element fails, which load drops?", and the answer should be visible on the single-line diagram. Load sharing between redundant units should also be monitored: a system built as N+1 may have quietly become N as loads were added over the years.

IEC 60364-7-710 and Medical Location Groups

IEC 60364-7-710 sets out particular requirements for electrical installations in medical locations and groups those locations by the nature of contact between patient and equipment. In general terms:

  • Group 0: Locations where no applied parts are used and where loss of supply poses no danger to the patient, for example rooms where no medical electrical equipment is applied to patients.
  • Group 1: Locations where applied parts are used externally or invasively on any part of the body other than the heart; an interruption is not life-threatening but may require an examination to be repeated.
  • Group 2: Locations such as intracardiac procedure rooms, operating theatres and intensive care, where loss of supply can endanger life.

The standard also classifies safety supplies by how quickly the source must take over. The shortest changeover classes cannot in practice be met by a generator and call for a UPS. For exact times and for which load belongs to which class, refer to the current edition of the standard and to national regulations, and state this mapping clearly, load by load, in the design documentation.

The Isolated IT System and Insulation Monitoring

In Group 2 locations, circuits feeding life-support and surgical equipment are typically supplied through a medical isolated IT system. In this arrangement the secondary side of an isolation transformer is not earthed, so a first insulation fault does not trip the circuit and supply continues while surgery is under way. However, the first fault effectively turns the system into an earthed one, so it must be detected before a second fault develops.

That task falls to the insulation monitoring device (IMD). The IMD continuously measures the insulation resistance of the system to earth and, when the threshold is crossed, gives an audible and visual warning at a place where medical staff can see it. In practice, overload and overtemperature of the isolation transformer are shown on the same alarm panel. The operational weak point is when these warnings never leave the room panel: if the technical team on the night shift learns about an IMD alarm only when a nurse phones them, the monitoring chain is incomplete.

Testing, Commissioning and Record Discipline

What proves that the critical power chain really works is not the design but the record. The following tests should be documented at commissioning and periodically afterwards:

  1. Mains failure simulation: Opening the main supply so that the ATS signals the generator, the generator accepts load and the retransfer takes place, with a timestamp for each step.
  2. Generator load test: Running under real load or a load bank while checking voltage and frequency stability.
  3. UPS test: Operation on battery, transfer to bypass and return to normal mode.
  4. IMD function test: Using the test button to confirm that the warning appears both in the room and at the remote monitoring point.
  5. Selectivity and thermal checks: Confirming that the protection coordination study is current and inspecting panel connections with a thermal camera.

Every record should include the date, the person who performed the test, the test duration, the load condition, any deviation observed and the action taken. Test intervals follow the manufacturer's instructions and the regulations in force. Paper forms work for audits but do not show trends; to see how the same test changes over the years, the measurements need to be stored as numerical data.

Monitoring Point Checklist

PointQuantity to MonitorWhy
Grid incomerPhase voltages, frequency, phase sequenceTimestamps for outages and voltage disturbances
TransformerLoad, temperature, power factorKnowing the remaining capacity when one transformer is out
ATSPosition (grid or generator), moment of transferEvidence that transfer and retransfer took place
GeneratorRunning status, run-time counter, fuel level, alarm bitsReadiness and matching against test records
UPSInput and output values, load, battery status, bypassMaking unprotected operating periods visible
Medical IT panelIMD warning output, isolation transformer load and temperatureDetecting a first insulation fault without delay
IT and server panelsPanel and PDU loadsWhether redundant paths are still truly redundant

Following the Chain on One Timeline with 6S Teknoloji

In 6S Teknoloji the field agent on site reads devices over Modbus TCP/RTU, M-Bus and BACnet/IP. From DSE generator control panels it collects fuel level, engine run time, mains-side and generator-side electrical values and alarm bits. On the UPS side, BACnet/IP reading uses a point map defined for the Vertiv Liebert EXL S1; there is no automatic discovery, and points are defined per model. As a result, the moment the grid dropped, the moment the generator took the load and the state of the UPS can be examined side by side on the same timeline.

If the connection is lost, readings are held in a local queue on site for 30 days and are not deleted until the server acknowledges them (ACK); on the server, the raw measurement series is kept for 13 months. The alarm engine sends e-mail notifications when defined conditions occur. In practice, this means the team can look back at how a test went using the stored measurements, and receives warnings by e-mail rather than only at the panel.

Related Content

Hospital Energy Monitoring — UPS & BackupUPS SNMP Monitoring: Battery, Load & RuntimeUPS Monitoring & Generator Tracking — 24/7real-time energy monitoringEPDK reactive limit monitoringearly transformer fault warningISO 50001 Energy Management GuideGenerator Fuel and Run Hour Monitoring

FAQ

Which links make up a hospital's critical power chain?
Grid and medium voltage, transformer, automatic transfer switch (ATS), generator, UPS and finally the medical and IT panels. For each link, the single-line diagram should show which load drops if that link fails.
What is the difference between N+1 and 2N redundancy?
N+1 adds one spare unit to the number of units required. 2N is an independent second copy of the system, duplicating distribution paths as well as units. Redundancy must exist along the path, not only in unit count.
How does 6S Teknoloji read critical power equipment?
The on-site field agent reads over Modbus TCP/RTU, M-Bus and BACnet/IP; fuel level, engine run time and alarm bits come from DSE generator panels. If the link drops, data is kept locally for 30 days and stored on the server for 13 months.

Monitor Your Facility with 6S Teknoloji

See 6S Teknoloji at Your Facility

Explore the system with your own data in a demo session.